- #Telemecanique altivar 08 manual english code#
- #Telemecanique altivar 08 manual english download#
- #Telemecanique altivar 08 manual english free#
If automated restart function is allowed (degree 2 parameter: Atr), these instructions are taken into account without to become reset just before.
If Atr USF automated restart is certainly only available for UFS problem no Return to factory settings (noYES) no Automatic injection braking current on end A 0.7 controller In Auto injection brake time on end if tdC 0: no brake if tdC 21: Cnt (constant braking on stop) will be shown Locking of parameters (noYES) if Okay: the parameters aré visible but cannót be modified éxcept fór L2A ánd LDC s 0.5 zero LDC (1) 4 rates of speed via LI3LI4: LSP benchmark AI1 if Ll3 0 and LI4 0 SP3 if LI3 0 and LI4 1 SP2 if LI3 1 and LI4 0 HSP if LI3 1 and LI4 1 Construction can only be improved with controller stopped Display Adjustment can become altered with controller ended or operating Analysis Unshielded source cable Screen Fault Treatment No problem displayed Motor doesnt operate although work command and quickness reference are OK After powered-up the get, the engine runs only if run commands have got been arranged to zero.
#Telemecanique altivar 08 manual english code#
#Telemecanique altivar 08 manual english download#
Telemecanique Altivar 08 English Download Papers For.
#Telemecanique altivar 08 manual english free#
Restoration Telemecanique Altivar 31 Error Troubleshooting Tutorial Telemecanique Altivar 31 Error.Impedance 5 t, 15 Sixth is v internal offer (11 Sixth is v to 15 Sixth is v) or 24 Sixth is v external supply (11 V to 30 Sixth is v) 15: Supply for reasoning advices: 15 Sixth is v, 100 mA max.Factory placing rdY Stopped: rate controller ready 45 Operating: estimated rotational frequency Hz dCb DC injection brake bFr ACC dEC LSP HSP SP2 SP3 ItH T2A no M2A Engine rate of recurrence: 50 Hz60 Hz (or SPE by modifying Fr5) Hz 50 Velocity ramp time s 3 Deceleration ramp period s 3 Low swiftness Hz 0 Large speed Hz 50 2nchemical preset velocity Hz 5 3rd preset swiftness Hz 25 A Thermal protection current ( engine rating plate) ifItH is certainly at potential.: ntH (safety disabled) will be displayed Control In Access to level 2 variables (noYES) no L2A Settings can only be improved with control halted To level 2 Modification can be improved with control ceased or operating Display Okay Level 2 parameters: function extensions FrH LCr ULn tHd tHr UnS Fr5 to level 1 UFr CrI FLG SLP Level 1 LI to level 1 Startup Alt Atr FCS IdC tdC LDC Function Unit Factory setting Display frequency setpoint Hz FrH Display motor current A Display supply voltage V Display speed controller thermal state (nominal 100, tripping at 118 ) Display motor thermal state (nominal 100, tripping at 118 ) Not memorized after loss of supply Nominal motor voltage (rating plate) V 230 Motor rated frequency (to be modified if other than 50 or 60 Hz 120 Hz max.) Hz bFr Minimum electric motor voltage at reduced frequency 20 IR settlement (adjust the stator resistance of the electric motor established by Ith) 20 Rate of recurrence loop get.If FLG 99, nFL (to deactivate this functionality may stall the electric motor when higher torque is definitely required) will be displayed.
0 kommentar(er)
